New H165 Loader

LOADERS
REQUEST A QUOTE
REQUEST A QUOTE
Key Features
  • Compatible with 3R Series Tractors
  • Quik-Park™ mounting system for efficient attachment and removal
  • Quik-Change attachment carrier makes it easier and faster to move from chore to chore
  • 1,122 pounds (509 kg) lift capacity

More Info

Features

Quik-change attachment carrier
Quik-change attachment carrierQuik-change attachment carrier

Allows fast, easy removal/mounting of attachments without tools.

End-of-pin lubrication means easy maintenance
Close up of grease fittingClose up of grease fitting
Pivot point grease fitting locationsPivot point grease fitting locations

All pivot points on the loader have grease fittings that are accessible from the side of the loader to make greasing the loader much easier, ensuring that all grease points are more likely to be serviced. No more searching for grease points that are hard to find. Removing the grease gun from the grease fitting or zerk is not a problem either as sufficient radius has been left to allow the grease gun tip to be rotated to the side for removal from the fitting or zerk.

Quik-Park™ loader mounting system
Quik-Park loader mounting systemQuik-Park loader mounting system

The H-Series Loaders are designed for easy removal and mounting to and from the tractor without tools.

The parking stand, attached to the front frame of the tractor, is an integral part of the loader during loader operation.

The parking stand lowers into position by moving the joystick to the raised position once the latches are opened. This allows the loader to move to the parked position.

To view a video of how the Quik-Park™ system works click here.

NOTE: This video only shows the dismount and mount of the loader without disconnecting the hydraulics. To completely remove the loader, the operator must turn the tractor off, relieve the hydraulics, and then disconnect the hoses from the couplers.

Specifications

Tractor
Model 3120/3320/3520/3720/3033R/3038R/3039R/3045R/3046R
Front tire 7.00-14 6PR R1
Rear tire 11.2-24 6PR R1
Front axle configuration
Wheelbase 1727 mm
68 in.
Pump capacity 8.6 gpm
Rated pressure 2500 psi
Loader
Leveling configuration
Bucket used
Bucket weight 93.8 kg
206.8 lb
Lift capacity at full height Measured at pivot (U)
725 kgf
1598 lbfMeasured at 500 mm ahead of pivot (V)
509 kgf
1122 lbf
Lift capacity at 59 in. (1500 mm) Measured at pivot (W)
964 kgf
2125 lbfMeasured at 500 mm ahead of pivot (X)
748 kgf
1649 lbf
Boom breakout force Measured at pivot (Y)
1509 kgf
3327 lbfMeasured at 500 mm ahead of pivot (Z)
1097 kgf
2417 lbf
Bucket rollback force capacity At maximum height (VV)
811 kgf
1787 lbfAt 59-in. (1500-mm) lift height (XX)
1349 kgf
2974 lbfAt ground-level line (ZZ)
1401 kgf
3087 lbf
Dimensions Maximum lift height (A)
2593 mm
102 in.At full height - bucket level(B)
2388 mm
94 in.At full height - bucket dumped (C)
2024 mm
79.7 in.
Overall length (I+F), ft (m) 3.207 m
10.52 ft
Overall height in carry position (J)
Digging depth (H) 143 mm
5.6 in.
Reach At maximum height (D)
562 mm
22.1 in.At ground level - bucket level (F)
1489 mm
58.6 in.
Bucket angle Dump angle, degrees (E)
41.1 degree (angle)Rollback angle, degrees (G)
31 degree (angle)
Cycle times Loader raise, seconds
3.56 secondsLoader lower, seconds
2.1 secondsBucket dump, seconds
2.96 secondsBucket rollback, seconds
1.75 seconds

Accessories and Attachments

Ballast Box

Ballast Box - BW15073
#

Ballast box can be used to carry additional ballast for greater tractor stability.

 

A 23-cm (9-in.) high extension can be added to ballast box for even greater capacity.

 

The hitch utilizes a standard Category 1 configuration for connection to the tractor Category 1 hitch.

 

A bushing kit is required for the ballast box to be used with the iMatch™ Quick-Hitch.

Ballast Box Extension - BW15074

Buckets

56 in. Dirt Bucket (12.3 cu. ft.) with Edge - AT332288
60 in. Dirt Bucket (14.3 cu. ft.) with Edge - AT333697
61 In. (1550 mm) Loader Heavy Duty Bucket with Holes for Cutting Edge - BW14764
Heavy-duty bucketsHeavy-duty buckets

Heavy-duty buckets are available for tasks requiring more robust bucket designs. Recommended for heavier use applications, such as commercial operations.

 

Top surface of the bucket is parallel to the cutting edge, which aids operator as a leveling guide.

 

Additional strength is built into the bucket design with additional wear bars, boxed top bucket section, and bucket end plate supports.

 

Cutting edge has pre-drilled holes for addition of a replaceable cutting edge.

61 In. (1550mm) Loader Materials Bucket - Quik Change - BW14146
1550-mm (61-in.) materials bucket1550-mm (61-in.) materials bucket

Materials buckets are available to match tractor-loader applications. The buckets may be used for loading dirt, gravel, feed, and light materials as well as scraping, digging, and other general-purpose tasks.

 

IMPORTANT: Materials buckets are not recommended for heavy-duty tasks. For heavier use applications, use heavy-duty bucket.

 

The top surface of the bucket is parallel to the cutting edge, which aids the operator as a leveling guide.

 

There is a quik-change connection for easy on and off.

 

The round-back design helps material flow when filling or dumping the bucket.

66 in. Construction Bucket (16.2 cu. ft.) with Edge - KV24751
66 in. Foundry Bucket (14.6 cu. ft.) - KV11636
66 in. Utility Bucket (20.6 cu. ft.) - KV22801
72 In. Quik-Tatch Standard Front Loader Bucket - LVB25341
72-in. Quik-Tatch standard-duty bucket72-in. Quik-Tatch standard-duty bucket

An economical standard-duty bucket is available for field installation. This bucket is recommended for light-duty applications. It does not include a bolt-on replaceable cutting edge.

 

NOTE: This bucket will ship from Quad Cities warehouse location.

73 In. (1850 mm) Loader Heavy Duty Bucket with Holes for Cutting Edge - BW14765
Heavy-duty bucketsHeavy-duty buckets

Heavy-duty buckets are available for tasks requiring more robust bucket designs. Recommended for heavier use applications, such as commercial operations.

 

Top surface of the bucket is parallel to the cutting edge, which aids operator as a leveling guide.

 

Additional strength is built into the bucket design with additional wear bars, boxed top bucket section, and bucket end plate supports.

 

Cutting edge has pre-drilled holes for addition of a replaceable cutting edge.

73 In. (1850 mm) Loader High Volume Bucket - BW14658
High-volume bucketHigh-volume bucket

This is a large-capacity bucket for the 300CX, H165, 400X, 400CX, and H180 Loaders for light material use such as handling mulch, sawdust, feed, and snow.

 

IMPORTANT: Not designed to withstand heavy material or usages other than light materials.

 

The top surface of the bucket is parallel to the cutting edge, which aids operator as a leveling guide.

 

Quick-change for easy on and off. 

 

Round-back design helps material flow when filling or dumping the bucket.

73 In. (1850mm) Loader Materials Bucket - BW14147
Materials bucketsMaterials buckets

Materials buckets are available to match tractor and loader applications. May be used for loading dirt, gravel, feed and light materials, as well as scrapping, digging and other general purpose tasks.

 

IMPORTANT: Materials buckets are not recommended for heavy-duty tasks. For heavier-use applications, use the heavy-duty bucket.

 

Top surface of the bucket is parallel to cutting edge, which aids operator as a leveling guide.

Quik-Change connection for easy on and off.

 

Round-back design helps material flow when filling or dumping the bucket.

85 In. (2150 mm) Loader High Volume Bucket - BW15273
High-volume bucketHigh-volume bucket

This is a large-capacity bucket for the 300CX, H165, 400X, 400CX, and H180 Loaders for light material use such as handling mulch, sawdust, feed, and snow.


 IMPORTANT: Not designed to withstand heavy material or usages other than light materials.

 

The top surface of the bucket is parallel to the cutting edge, which aids operator as a leveling guide.

 

Quick-change for easy on and off. 

 

Round-back design helps material flow when filling or dumping the bucket.

Cutting Edges

56 in. Bolt-On Cutting Edge - T225190
60 in. Bolt-On Cutting Edge - KV17819
61 In. (1550 mm) Replaceable Bucket Cutting Edge with Hardware - BW14762

Recommended for heavier use applications, such as commercial operations and rental customers.

 

Additional strength is added to the cutting edge and the replaceable cutting edge is reversible for longer wear life.

 

Not compatible with tooth bars.

 

NOTE:  Heavy-duty buckets come standard with the holes to install the replaceable cutting edge.  Standard materials buckets require installation of attaching holes.

73 In. (1850 mm) Replaceable Bucket Cutting Edge with Hardware - BW14763
Bucket cutting edgeBucket cutting edge
Closeup of cutting edgeCloseup of cutting edge
Hardware for cutting edgeHardware for cutting edge

Recommended for heavier-use applications, such as commercial operations and rental customers. Additional strength is added to the cutting edge. Replaceable and reversible cutting edge for longer wear life.

 

DECAL KIT

Text Free Decals for Export - BW16329

HITCH ADAPTERS

iMatch Bushing Kit - BW15056
iMatch quick-coupler bushing kitiMatch quick-coupler bushing kit

Bushing kit for use with Category 1 implements (ballast box) to make them function correctly with the iMatch Quick-Hitch.

Hood Guards

Deluxe Hood Guard Attachment - BW15222
Deluxe hood guard attachmentDeluxe hood guard attachment

Hood guard attachment to make BW15219 or BW15221 into a deluxe hood guard.

Deluxe Hood Guard Attachment - BW16585
Deluxe hood guard attachmentDeluxe hood guard attachment

Hood guard attachment to make BW15219 or BW15221 into a deluxe hood guard.

Hood Guard - BW14378
Hood guard for 4000 and 4010 Series TractorsHood guard for 4000 and 4010 Series Tractors

A hood guard can be ordered for a tractor without ordering a loader.

 

The hood guard protects the front of the tractor while operating the loader.

 

The bolt-on design stays with tractor when loader is removed.

Hood Guard - BW15219
Hood guard for 3000 TWENTY Series TractorsHood guard for 3000 TWENTY Series Tractors

A hood guard can be ordered for a tractor without ordering a loader.

 

The hood guard protects the front of the tractor while operating the loader.

 

The bolt-on design stays with tractor when loader is removed.

 

The hood guard for the 3000 TWENTY Series Tractors pivots forward to allow the tractor hood to be raised.

Hood Guard - BW15416

A hood guard can be ordered for a tractor without ordering a loader.

 

The hood guard protects the front of the tractor while operating the loader.

 

The bolt-on design stays with tractor when loader is removed.

Hood Guard - BW16617

A hood guard can be ordered for a tractor without ordering a loader.

The hood guard protects the front of the tractor while operating the loader.

The bolt-on design stays with tractor when loader is removed.

Hood Guard (3005, 4005) - BW15848
Hood guard for 4105 TractorsHood guard for 4105 Tractors

A hood guard can be ordered for a tractor without ordering a loader.
 
The hood guard protects the front of the tractor while operating the loader.
 
The bolt-on design stays with tractor when loader is removed. This hood guard is required for 300CX, H165 Loader installation on the 4105 Tractor.

Hood Guard (3203) - BW15534

A hood guard can be ordered for a tractor without ordering a loader.

The hood guard protects the front of the tractor while operating the loader.

The bolt-on design stays with tractor when loader is removed. 

Hood Guard (4105) - BW16040
Hood guard for 4105 TractorsHood guard for 4105 Tractors

A hood guard can be ordered for a tractor without ordering a loader.
 
The hood guard protects the front of the tractor while operating the loader.
 
The bolt-on design stays with tractor when loader is removed. This hood guard is required for 300CX, H165 Loader installation on the 4105 Tractor.

Hydraulics

Hoses and Parts - BW15352
Hoses and Parts - BW15599
Hoses and Parts - BW15762
Hydraulic Lines and Hoses (3 Function) - BW16138

Provides hydraulic couplers at the front of the loader boom for operating attachments that require third-function hydraulics.

NOTES:

  1. Tractor must be equipped with a third SCV.
  2. If used with skid steer attachments, the couplers will not match. The following parts are required to convert for this application:
  • 1- KV14216
  • 1- KV15976
  • 2- AT191333

Miscellaneous

66 in. Bolt-On Cutting Edge - U16748
72 in. Bolt-On Cutting Edge - T32742
Anti -Drop Valve Kit - Bucket Circuit - BW16050
Anti -Drop Valve Kit - Lift Circuit - BW16049
Bucket Level Indicator - BW15223
Bucket level indicatorBucket level indicator

The bucket level indicator assists the operator to determine the attachment position at ground level.

 

It is adjustable to indicate level position for different attachments such as pallet forks and buckets.

 

The indicator is adjusted to have the bend of the rod rest in the bracket when the attachment is level at ground.

Skid Steer Attachment Carrier - BW15244
Skid steer attachment carrierSkid steer attachment carrier

The skid steer attachment carrier is installed in place of the standard John Deere attachment carrier and allows for the use of skid steer attachments on the 300CX, H160, H165, H180, 400X and 400CX Loaders.

Skid steer attachments are available through Worksite Pro™ attachments.

Miscellaneous (Australia Only)

Anti Spill Kit - BW16253
Anti Spill Kit - BW16324
Anti Spill Kit - BW16605
Australian Code of Practice Kit - BW16244
Service Lock - BW16607

Mounting Frames

Mounting Frame - BW15347

Mounting frames are designed at the same time as the tractor in order to provide durable and yet very simple attaching points for the loader. The mounting frames bolt to the tractor chassis and do not restrict tractor use when the loader is not installed.

Mounting Frame (3320-3720, 4320-4720 Cab Tractors) - BW15456
Cab mounting frameCab mounting frame

Mounting frames are designed at the same time as the tractor in order to provide durable and yet very simple attaching points for the loader. The mounting frames bolt to the tractor chassis and do not restrict tractor use when the loader is not installed.

Mounting Frame (4105) - BW15682
Mounting Frame (4200-4400, 4210-4400, 3120-3720, 3203 Open Station Tractors) - BW15204
Open-station mounting frameOpen-station mounting frame

Mounting frames are designed at the same time as the tractor in order to provide durable and yet very simple attaching points for the loader. The mounting frames bolt to the tractor chassis and do not restrict tractor use when the loader is not installed.

Tooth Bars

56 in. Tooth Bar - 6 Teeth - AT337951
61 In. (1550 mm) Tooth Bar for Bucket - BW15227
Tooth barTooth bar

The tooth bar helps penetrate hard-packed material.  It attaches to the bucket by sliding over the cutting edge and is retained by two bolts, one in each end plate of the bucket.

  • Holes must be drilled in bucket end plates to retain the tooth bar
  • Protrudes beyond bucket edge approximately 150 mm or 6 in.
  • Recommended for use with heavy-duty buckets only
  • Not compatible with buckets with replaceable cutting edge installed
73 In. (1850 mm) Tooth Bar for Bucket - BW15228
Tooth barTooth bar

The tooth bar helps penetrate hard-packed material.  It attaches to the bucket by sliding over the cutting edge and is retained by two bolts, one in each end plate of the bucket.

  • Holes must be drilled in bucket end plates to retain the tooth bar
  • Protrudes beyond bucket edge approximately 150 mm or 6 in.
  • Recommended for use with heavy-duty buckets only
  • Not compatible with buckets with replaceable cutting edge installed